page 1 the big deal: product overview: YSF-272+ is an advanced amplifer module in a mini-circuits system in package ? . this module is fully matched to 50 ? in/out impedance and has built-in input & output dc block capacitors. it is enclosed in a 5 x 6 mm mclp plastic package. the YSF-272+ uses e-phemt technology enabling it to work with a single positive supply voltage. feature advantages superior gain flatness 0.7db the YSF-272+ provides industry leading gain fatness over the 2ghz wimax and umts bands (2.3,2.5 and 2.5 to 2.7ghz) making this ideal for use in applications where gain-fatness and repeatability are critical performance requirements. high gain the YSF-272+ is a two-stage design with internal feedback and bias to provide fat 20 db nominal gain, supporting applications where a single gain block must overcome large system losses such as long cable runs and lossy components. strong combination of performance the YSF-272+ provides a strong combination of performance parameters including high gain (20 db), high ip3 (+35 dbm) and p1db (+20 dbm) and low noise fgures (2.4 db) that are diffcult to achieve in a single stage design and available only in the ysf amplifer series. integrated matching, dc blocking and bias in small package the YSF-272+ includes all support circuits including: matching, bias and dc block - ing, all integrated into a single 5x6mm package making the total footprint equal to or smaller than most solutions. excellent return loss the YSF-272+ includes integrated input and output matching and bias circuits to make this amplifer a simple, complete drop-in solution. the matching circuits provide excellent output return loss (20db), and are designed to give optimal p1db and ip3 performance in a 50 ? environment. high reverse isolation with 30 db of reverse isolation C the YSF-272+ is an ideal gain block for use in inte - grated systems to minimize vswr interactions resulting from cascading highly refec - tive components such as sharp flters. YSF-272+ key features ? mini-circuits system in package flat gain amplifer ? ultra flat gain response: 0.7 db over 2300-2700 mhz ? excellent combination of gain, p1db, ip3 and nf ? 50 ? input and output: no external components required case style: dl1020 iso 9001 iso 14001 as 9100 certified min i-cir cuits ? p . o . b ox 3 50166, b r ooklyn, new y ork 1 1 2 3 5-0 003 ( 7 18) 9 3 4-4 500 fax ( 7 1 8 ) 332-4661 the design engi ne ers search engi ne provides actual d ata in stantly a t ? notes: 1. performance and quality attributes and conditions not expr essly stated in this specification sheet ar e intended to be excluded and do not form a part of this specification sheet. 2. electrical specifications and performance data contained her ein ar e based on mini-cir cuit? s applicable established test performance criteria and measur ement instructions. 3. the parts cover ed by this specification sheet ar e subject to mini-cir cuits standar d limited warranty and terms and conditions (collectively , ?standar d t erms?) ; pur chasers of this part ar e entitled to the rights and benefits contained ther ein. for a full statement of the standar d t erms and the exclusive rights and r emedies ther eunder , please visit mini-cir cuits? website at www .minicir cuits.com/mclstor e/terms.jsp. for detailed performance specs & shopping online see web site min icir cuits.c o m if/rf microw a ve components
page 2 product features ? matched 50-ohm surface mount amplifer ? high gain, 19 db typ. ? up to +20 dbm typ. output power ? high ip3, +35 dbm ? low noise figure, 2.5 db typ. ? high directivity, 30 db isolation ? internal input & output dc block ? separate terminal for dc 2.3-2.7 ghz YSF-272+ case style: dl1020 price: $2.59 ea. qty. (20) + rohs compliant in accordance with eu directive (2002/95/ec) the +suffx has been added in order to identify rohs compliance. see our web site for rohs compliance methodologies and qualifcations. typical applications ? wimax ? portable wireless ? receivers & transmitters ? radar general description YSF-272+ is an advanced amplifer module in a mini-circuits system in package ? . this module is fully matched to 50 ? in/out impedance and has built-in input & output dc block capacitors. it is enclosed in a 5 x 6 mm mclp plastic package. the YSF-272+ uses e-phemt* technology enabling it to work with a single positive supply voltage. simplifed schematic and pad description function pad number description rf-in 5 rf input rf-out 3 rf output dc 4 dc supply gnd paddle connected to ground not used 1,2,6,7,8 no internal connection *enhancement mode pseudomorphic high electron mobility transistor ? mini-circuits system in package flat gain amplifer 8 nc 7 nc 6 nc 5 rf in nc 1 nc 2 rf out 3 dc in 4 paddle rf in rf out dc rev. or m128712 YSF-272+ 110203 iso 9001 iso 14001 as 9100 certified min i-cir cuits ? p . o . b ox 3 50166, b r ooklyn, new y ork 1 1 2 3 5-0 003 ( 7 18) 9 3 4-4 500 fax ( 7 1 8 ) 332-4661 the design engi ne ers search engi ne provides actual d ata in stantly a t ? notes: 1. performance and quality attributes and conditions not expr essly stated in this specification sheet ar e intended to be excluded and do not form a part of this specification sheet. 2. electrical specifications and performance data contained her ein ar e based on mini-cir cuit? s applicable established test performance criteria and measur ement instructions. 3. the parts cover ed by this specification sheet ar e subject to mini-cir cuits standar d limited warranty and terms and conditions (collectively , ?standar d t erms?) ; pur chasers of this part ar e entitled to the rights and benefits contained ther ein. for a full statement of the standar d t erms and the exclusive rights and r emedies ther eunder , please visit mini-cir cuits? website at www .minicir cuits.com/mclstor e/terms.jsp. for detailed performance specs & shopping online see web site min icir cuits.c o m if/rf microw a ve components
page 3 flat gain amplifer electrical specifcations (1) at 25c, zo=50 ? unless noted YSF-272+ parameter condition (mhz) min. typ. max. units frequency range 2300 2700 mhz gain 2300 17.6 19.5 21.5 db 2500 17.1 19.0 21.5 2700 16.2 18.0 20.5 gain flatness 0.7 db input return loss 2300 12.6 db 2500 10.0 15.0 2700 18.0 output return loss 2300 20.0 db 2500 12.0 17.0 2700 14.0 reverse isolation 30.0 db output power @1 db compression 2300 20.0 dbm 2500 18.0 20.0 2700 20.0 output power @3 db compression 21.0 dbm output ip3 2300 34.0 dbm 2500 30.0 35.0 2700 35.0 noise figure 2300 2.5 db 2500 2.5 3.5 2700 2.5 device operating voltage 5 v device operating current 118 145 ma device current variation vs. temperature (2) 2 a/c device current variation vs voltage 0.002 ma/mv thermal resistance, junction-to-ground lead (3) 56 c/w absolute maximum ratings parameter ratings units operating temperature (4) -40 to 85 c storage temperature -65 to 150 c dc voltage on pad 4 7 v power dissipation 1.5 w input power 21 dbm note: permanent damage may occur if any of these limits are exceeded. these ratings are not intended for continuous normal operation. (4) case is defned as ground paddle. (1) measured on mini-circuits characterization test board tb-589+. see characterization test circuit (fig. 1) (2) d (+85c to -45c) (3) thermal resistance= hot spot temperature - ground lead temperature power dissipation dc current histogram 9 0 9 5 10 0 10 5 11 0 11 5 12 0 12 5 13 0 13 5 14 0 14 5 15 0 15 5 dc current (ma) usl usl=upper spec limit iso 9001 iso 14001 as 9100 certified min i-cir cuits ? p . o . b ox 3 50166, b r ooklyn, new y ork 1 1 2 3 5-0 003 ( 7 18) 9 3 4-4 500 fax ( 7 1 8 ) 332-4661 the design engi ne ers search engi ne provides actual d ata in stantly a t ? notes: 1. performance and quality attributes and conditions not expr essly stated in this specification sheet ar e intended to be excluded and do not form a part of this specification sheet. 2. electrical specifications and performance data contained her ein ar e based on mini-cir cuit? s applicable established test performance criteria and measur ement instructions. 3. the parts cover ed by this specification sheet ar e subject to mini-cir cuits standar d limited warranty and terms and conditions (collectively , ?standar d t erms?) ; pur chasers of this part ar e entitled to the rights and benefits contained ther ein. for a full statement of the standar d t erms and the exclusive rights and r emedies ther eunder , please visit mini-cir cuits? website at www .minicir cuits.com/mclstor e/terms.jsp. for detailed performance specs & shopping online see web site min icir cuits.c o m if/rf microw a ve components ?
page 4 flat gain amplifer fig 1 . block diagram of test circuit used for characterization. (dut soldered on mini-circuits characterization test fixture tb-589+) gain, return loss, output power at 1db compression (p1 db), output ip3 (oip3) and noise figure measured using agilents n5242a pna-x microwave network analyzer. conditions: 1. gain: pin= -25dbm 2. output ip3 (oip3): two tones, spaced 10 mhz apart, 2.5 dbm/tone at output. characterization test circuit recommended application circuit (refer to evaluation board for pcb layout and component values) fig 2. recommended application circuit YSF-272+ product marking ysf index over pin 1 rf-in rf-out vs (supply voltage) 5 4 3 tb-589+ rf-in rf-out vs 5 4 3 c1 paddle iso 9001 iso 14001 as 9100 certified min i-cir cuits ? p . o . b ox 3 50166, b r ooklyn, new y ork 1 1 2 3 5-0 003 ( 7 18) 9 3 4-4 500 fax ( 7 1 8 ) 332-4661 the design engi ne ers search engi ne provides actual d ata in stantly a t ? notes: 1. performance and quality attributes and conditions not expr essly stated in this specification sheet ar e intended to be excluded and do not form a part of this specification sheet. 2. electrical specifications and performance data contained her ein ar e based on mini-cir cuit? s applicable established test performance criteria and measur ement instructions. 3. the parts cover ed by this specification sheet ar e subject to mini-cir cuits standar d limited warranty and terms and conditions (collectively , ?standar d t erms?) ; pur chasers of this part ar e entitled to the rights and benefits contained ther ein. for a full statement of the standar d t erms and the exclusive rights and r emedies ther eunder , please visit mini-cir cuits? website at www .minicir cuits.com/mclstor e/terms.jsp. for detailed performance specs & shopping online see web site min icir cuits.c o m if/rf microw a ve components ?
page 5 flat gain amplifer YSF-272+ esd rating human body model (hbm): class 1a in accordance with ansi/esd stm 5.1 - 2001 machine model (mm): class m1 (25v) in accordance with ansi/esd stm5.2-1999 msl rating moisture sensitivity: msl1 in accordance with ipc/jedec j-std-020d attention observe precautions for handling electrostatic sensitive devices visual inspection electrical test sam analysis refow 3 cycles, 260c soak 85c/85rh 168 hours bake at 125c, 24 hours visual inspection electrical test sam analysis start msl test flow chart additional detailed technical information (additional information is available on our web site. to access this information enter the model number on our web site home page) performance data data table go! swept graphs go! s-parameter (s2p files) data set (.zip fle) go! case style dl1020 plastic package, exposed paddle, lead fnish: tin/silver/nickel go! tape & reel f68 go! standard quantities available on reel 7 reels with 20, 50, 100, 200, 500, or 1k devices. suggested layout for pcb design pl-335 go! evaluation board tb-589-5+ go! environmental ratings env08t1 go! iso 9001 iso 14001 as 9100 certified min i-cir cuits ? p . o . b ox 3 50166, b r ooklyn, new y ork 1 1 2 3 5-0 003 ( 7 18) 9 3 4-4 500 fax ( 7 1 8 ) 332-4661 the design engi ne ers search engi ne provides actual d ata in stantly a t ? notes: 1. performance and quality attributes and conditions not expr essly stated in this specification sheet ar e intended to be excluded and do not form a part of this specification sheet. 2. electrical specifications and performance data contained her ein ar e based on mini-cir cuit? s applicable established test performance criteria and measur ement instructions. 3. the parts cover ed by this specification sheet ar e subject to mini-cir cuits standar d limited warranty and terms and conditions (collectively , ?standar d t erms?) ; pur chasers of this part ar e entitled to the rights and benefits contained ther ein. for a full statement of the standar d t erms and the exclusive rights and r emedies ther eunder , please visit mini-cir cuits? website at www .minicir cuits.com/mclstor e/terms.jsp. for detailed performance specs & shopping online see web site min icir cuits.c o m if/rf microw a ve components ?
|
